 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| AMP I RE SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED BY DATE Approved For Specifications Approved For Specifications & Sample AO-162MGA00 APPROVED BY CHECKED BY ORGANIZED BY DATE:2004/9/30 AMPIRE CO., LTD. 1 RECORD OF REVISION Revision Date 2004/5/5 2004/5/21 Page P.3 P.4 P.7 P.10 P.12 2004/7/1 2004/9/27 P.6 New Release Modify the operating temp min to -10 degrees Modify input voltage and logic supply current Add the pin connections diagram Modify ambient temperature to 20 degrees Modify reliability low temperature operation Modify the C1~C8 and C9~C16 Layout. Modify the LCD data according the prototype Modify the C1~C8 and C9~C16 Layout according the NT7651 ver1.0 data sheet. Add LCD initial setting 2004/9/30 Modify the pin length to 9.0min kokai Kokai Kokai Contents Editor Sam DATE:2004/9/30 AMPIRE CO., LTD. 2 1 FEATURES (1) Display format : 16 characters x 2 lines (2) Display type: STN Gray, Reflective, 6 o'clock view, Positive (3) Controller : NT7651H-BDT02 (4) I2C Interface (5) Adopt COG Technology 2 MECHANICAL DATA Parameter Dot size Dot pitch Character size Viewing area Module size Stand Value 0.55(W) x 0.6(H) 0.6(W) x 0.65(H) 2.95(W) x 5.15(H) 61.0(W) x 13.7(H) 66.0(W) x 27.7(H) Unit mm mm mm mm mm 3 ABSOLUTE MAXIMUM RATINGS Parameter Logic Circuit Supply Voltage LCD Driving Voltage Input Voltage Symbol VDD-VSS VLCD VIN TOP TSTG Min 0 0 VSS -10 -20 Max 3.5 6.5 VDD 50 70 Unit V V V C C Normal temp. type Operating Temp. Storage Temp. DATE:2004/9/30 AMPIRE CO., LTD. 3 4 ELECTRO-OPTICAL CHARACTERISTICS Parameter Logic Circuit Supply Voltage LCD Driving Voltage ( STN ) Input Voltage Logic Supply Current Contrast Rise Time Fall Time Viewing Angle Range Symbol Condition Min Typ Max Unit Note ----- Electronic Characteristics ----VDD-VSS VLCD -0 C 25 C 50 C VIH VIL IDD --VDD = 3.3V 25C 25C 25C 25C & CR2 -4.5 4.4 4.3 0.8VDD VSS -3.3 4.6 4.5 4.4 --0.2 -4.7 4.6 4.5 VDD 0.2VDD -V V mA V V . ----- Optical Characteristics ( STN ) ----CR tr tf f b l r Frame Frequency fF 25C --------5.2 120 250 40 35 35 35 64 -180 400 -----Hz Deg. ms ms Note 3 Note 1 Note 2 (NOTE 1) Contrast ratio : CR = (Brightness in OFF state) / (Brightness in ON state) DATE:2004/9/30 AMPIRE CO., LTD. 4 ( NOTE 2 ) Response time : (NOTE 3) Viewing angle DATE:2004/9/30 AMPIRE CO., LTD. 5 5 BLOCK DIAGRAM DATE:2004/9/30 AMPIRE CO., LTD. 6 6 PIN CONNECTIONS 16 x 2 C C R R=10K , C=0.1uF PIN NO. SYMBOL 1 VLCD 2 VSS 3 VDD 4 SDA 5 POR 6 SCL LEVEL H/L H/L H/L FUNCTION Internal Generated LCD Bias Voltage Power Ground Logic Power Supply Serial Data Input/Output External Power On Reset Serial Clock Input DATE:2004/9/30 AMPIRE CO., LTD. 7 7 LCD Initial Setting LCD_INIT: LCALL IC_START MOV A,#01110100B ;SLAVE ADDRESS LCALL SEND_BYTE MOV A,#00H ;SEND A CONTROL BYTE LCALL SEND_BYTE MOV A,#00110100b; ;FUNCTION SET 00100010 ; 001 DL,0,M SL,H LCALL MOV SEND_BYTE A,#0CH ;DISPLAY ON LCALL SEND_BYTE LCALL DELAY1S MOV LCALL MOV LCALL MOV LCALL A,#06H SEND_BYTE A,#00110101b; SEND_BYTE A,#10011111b; SEND_BYTE ;FUNCTION SET ; 001 DL,0,M SL,H ;VA=1 21h 00100010 ;ENTRY MODE SET ; VLCD = (integer value of register* 0.082) + 1.8=4.5v ;integer value of register=21h LCALL DELAY1S MOV A,#00110100b; ;FUNCTION SET ; 001 DL,0,M SL,H 00100010 LCALL SEND_BYTE ACALL RET IC_STOP DATE:2004/9/30 AMPIRE CO., LTD. 8 8 TIMING CHARACTERISTICS Write Operation DATE:2004/9/30 AMPIRE CO., LTD. 9 9 FONT TABLE DATE:2004/9/30 AMPIRE CO., LTD. 10 10 QUALITY AND RELIABILITY 10.1 TEST CONDITIONS Tests should be conducted under the following conditions : Ambient temperature : 20 5C Humidity : 60 25% RH. 10.2 SAMPLING PLAN Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan . 10.3 ACCEPTABLE QUALITY LEVEL A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation. 10.4 APPEARANCE An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits. DATE:2004/9/30 AMPIRE CO., LTD. 11 10.5 INSPECTION QUALITY CRITERIA Item Function Dimension Black spots Description of defects Class of Defects Major Major Minor Acceptable level (%) 0.65 1.5 2.5 Black lines Bubbles in polarizer Color uniformity Glass Scratches Contrast ratio Response time Viewing angle Short circuit or Pattern cut Deviation from drawings Ave . dia . D area A area B Disregard D0.2 3 4 0.2 Minor 2.5 Minor Minor Minor Minor Minor Minor 2.5 2.5 2.5 2.5 2.5 2.5 Zone A active area Zone B viewing area DATE:2004/9/30 AMPIRE CO., LTD. 12 10.6 RELIABILITY Test Conditions Test Item High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Temperature Cycle Humidity Test Normal Temp. type 503C , t=96 hrs -103C , t=96 hrs 603C , t=96 hrs -203C , t=96 hrs -20C ~ 25C ~ 60C 30 min. 5 min. 30 min. ( 1 cycle ) Total 5 cycle 40 C, Humidity 90%, 96 hrs 1,2 1,2 1,2 1,2 Note Sweep frequency : 10 ~ 55 ~ 10 Hz/1min Amplitude : 0.75mm 2 Vibration Test (Packing) Test direction : X.Y.Z/3 axis Duration : 30min/each axis Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35C , 45-65%RH). Definitions of life end point : Current drain should be smaller than the specific value. Function of the module should be maintained. Appearance and display quality should not have degraded noticeably. Contrast ratio should be greater than 50% of the initial value. DATE:2004/9/30 AMPIRE CO., LTD. 13 11 HANDLING PRECAUTIONS (1) A LCD module is a fragile item and should not be subjected to strong mechanical shocks. (2) Avoid applying pressure to the module surface. This will distort the glass and cause a change in color. (3) Under no circumstances should the position of the bezel tabs or their shape be modified. (4) Do not modify the display PCB in either shape or positioning of components. (5) Do not modify or move location of the zebra or heat seal connectors. (6) The device should only be soldered to during interfacing. Modification to other areas of the board should not be carried out. (7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make contact with the skin. If contact is made rinse immediately. (8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or Ethyl alcohol. The use of water, ketone or aromatic is not permitted. (9) Prior to initial power up input signals should not be applied. (10) Protect the module against static electricity and observe appropriate anti-static precautions. DATE:2004/9/30 AMPIRE CO., LTD. 14 12 OUTLINE DIMENSION i DATE:2004/9/30 AMPIRE CO., LTD. o u q 15 |
Price & Availability of AO-162MGA00
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |